TRACING PLUS line marking spray paint

Highly resistant line marking paint

By box unit

The TRACING PLUS paint is intended more for marking lines on high-wear surfaces, for example inside factories and logistical warehouses due to its tremendous resistance to grime. This line marking spray paint is packaged in 750 ml containers for lasting, economical marking, particularly inside...

More details


Data sheet

Volume 750 ml
Packaging Box of 6 cans
Product type Line marking spray paint
Application domain Line marking, Ground signage, Signalling and events
Application area Concrete, Bitumens, Metal, ...

Download

More info


TRACING® PLUS  : THE HIGHLY RESISTANT LINE MARKING SPRAY PAINT,
IDEAL SOLUTION FOR FACTORIES OR LOGISITICAL WAREHOUSES

 

 

Properties of the TRACING line marking spray paint

 

  • Excellent adhesion and high resistance to mechanical wear.
  • Excellent resistance to dirt.
  • Crisp, sharp lines thanks to its purpose designed nozzle.
  • Rapid drying: approximately 15 to 20 min.
  • Marking duration: approximately 12 months, depending on the application surface, usage and wear.
  • Application temperature: from +5°C to 50°C.
  • NSF “non-food compound” certified, usable in food storage areas or where food products are manufactured.
    NSF is the most know organism over the World. Registration number 149 448. Catregory code P1.

 

Line width 4 cm to 10 cm 1 x 750 ml aerosol
coat coats
Slow application 100 m 50 m
Rapid application 150 m 75 m

 

Specifications of the TRACING line marking spray paint

 

nsf certification soppec tracing plus

NSF Certification :

Tracing Plus products can be used in premises where food products are stored or manufactured.

Composition

Binder: acrylic and alkyd urethane blend
Pigments: mineral and organic, free from lead and cadmium
Solvents: a complex blend free from chlorinated solvents and aromatic compounds (toluene, xylene, etc)
Propellant: dimethyl ether

Application method

Manually or using our application equipment (line marking equipmentmarking paint gun, see bellow)
Drying Time: 15 to 20 min

Health and safety

Safety data sheets are available free of charge on the internet: www.quick-fds.com.
No paint mist or drips during use.
CLP labelling with a single pictogram.

DANGER
H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.

picto inflammable

 

Recommendation for use

 

  • Use head down, adjust the position of the aerosol in the equipment used to give an application height that produces the desired line width.
  • BEFORE USE: Shake the can vigorously in an upside down position to thoroughly mix the paint, continue shaking even after having clearly heard the ball bearings.
  • AFTER USE: Purge head up (until gas only comes out) to clean the valve and nozzle.

 

General conditions for use

 

Whatever the nature of the surface, the following conditions are essential for the optimal application of TRACING® PLUS :
Correct preparation of the surface to be painted is imperative to obtain excellent paint adhesion.
Thoroughly clean the surface to ensure that it is free from dust, dirt, grease, etc.
Relative humidity should be between 10% and 50%.
The application temperature should not be below 5°C.
For a good quality line, the first coat should be applied quickly (print layer); on the other hand the second and optional third coats should be applied more slowly to obtain the desired coverage.

 

Recommendations by surface type

 

CONCRETE

Before applying TRACING PLUS® to a new concrete surface, allow a minimum of 3 to 4 weeks for complete drying (French building trades standards) and the elimination of acidity.

ASPHALT

It is advisable to wait at least 15 days before line-marking a new asphalt surface in order to avoid any alteration to the quality of the marking.

Special conditions applicable to “synthetic” (plastic, PVC, varnishes) and painted (epoxy, PU) floor surfaces.

n this domain, there are several different types of paint and the paint used for the floor may be incompatible with TRACING® PLUS (resulting in poor adhesion). We therefore recommend carrying out a test beforehand for these specific types of surface.

Lines can be given a protective coating of our PROTECT LINE varnish for improved longevity and dirt resistance.

 

 


Associated products