TRACING Line marking spray paint

Line marking paint

By box unit

TRACING® line marking spray paint is used to delimit surface areas and optimise traffic by tracing lines inside or out: Logistical warehouses, sports complexes, grassed pitches, cycling tracks and car parks. This line marking paint is intended more for ground markings on surfaces with little wear. It is the best quality/cost compromise for outside marking.

More details

114,60 €

Volume discounts

Quantity (by box unit)DiscountYou Save
10 7,20 € Up to 72,00 €

Data sheet

PackagingBox of 12 cans
Volume500 ml, 750 ml
Marking time12 months
Product typeLine marking spray paint
Application domainLine marking, Signalling and events, Ground signage
Application areaConcrete, Bitumens, Metal, ...

Download

More info


TRACING® : THE EASY TO USE LINE MARKING SPRAY PAINT
WITH THE BEST QUALITY / PRICE COMPROMISE

 

 

The 750ml offers the best value for money for outdoor marking.

 

Properties of the TRACING line marking spray paint

 

  • Excellent adhesion.
  • Good weather resistance and fast drying: 15 to 20 minutes or less.
  • Crisp, sharp lines thanks to its purposedesigned nozzle.
  • Application temperature: from +5°C to 50°C.
  • Aerosol cans, volume 600 ml / 500 ml net, in boxes of 12.
  • Aerosol cans, volume 1000 ml / 750 ml net, in boxes of 6.

  

DANGEROUS. FOLLOW THE PRECAUTIONS.

 

Line width 4 cm to 10 cm1 x 500 ml aerosol1 box of 12 x 500 ml aerosols1 x 750 ml aerosol
coatcoatscoatcoatscoatcoats
Slow application50 m25 m600 m300 m100 m50 m
Rapid application75 m37 m900 m450 m150 m75 m

 

Specifications of the TRACING line marking spray paint

 

Composition

Binder: acrylic
Pigments: mineral and organic, lead and cadmium-free
Solvents: a complex blend free from chlorinated solvents and aromatic compounds (toluene, xylene, etc)
Propellant: a specific mix of isobutane and propane

Application method

Manually or using our application equipment (line marking equipment, marking paint gun, see bellow)
Drying Time: 15 to 20 min

Health and safety

Safety data sheets are available free of charge on the internet: www.quick-fds.com.
No paint mist or drips during use.
CLP labelling with a single pictogram.

DANGER

H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.
EUH208 Contains TALL OIL FATTY ACIDS,COMPOUNDS WITHOLEYLAMINE. May produce an allergic
reaction.

picto inflammable

 

Recommendation for use

 

  • Use head down, adjust the position of the aerosol in the equipment used to give an application height that produces the desired line width.
  • BEFORE USE: Shake the can vigorously in an upside down position to thoroughly mix the paint, continue shaking even after having clearly heard the ball bearings.
  • AFTER USE: Purge head up (until gas only comes out) to clean the valve and nozzle.

 

General conditions for use

 

Whatever the nature of the surface, the following conditions are essential for the optimal application of TRACING®
Correct preparation of the surface to be painted is imperative to obtain excellent paint adhesion.
Thoroughly clean the surface to ensure that it is free from dust, dirt, grease, etc.
Relative humidity should be between 10% and 50%.
The application temperature should not be below 5°C.
For a good quality line, the first coat should be applied quickly (print layer); on the other hand, the second and optional third coats should be applied more slowly to obtain the desired coverage.

 

Recommendations by surface type

 

CONCRETE

Before applying Tracing® to a new concrete surface, allow a minimum of 3 to 4 weeks for complete drying (French building trades standards) and the elimination of acidity.

ASPHALT

It is advisable to wait at least 15 days before line-marking a new asphalt surface in order to avoid any alteration to the quality of the marking.

Special conditions applicable to “synthetic” (plastic, PVC, varnishes) and painted (epoxy, PU) floor surfaces.

In this domain, there are several different types of paint and the paint used for the floor may be incompatible with TRACING® (resulting in poor adhesion). We therefore recommend carrying out a test beforehand for these specific types of surface.

Lines can be given a protective coating of our PROTECT LINE varnish for improved longevity and dirt resistance.


Associated products